PVC cake armature #1: Brobee 3D cake

PVC “HOW TO”

I am still a new cake artist, and am far from perfect. I had an order for a children’s birthday party, in which the customer wanted a 3D character from a popular children’s show, Yo Gabba Gabba. I searched all over Cakesdcor and CC, as wellk as on the web, and was not able tyo find very many tutorials, let alone info on how to build PVC armature. I found a premade armature set on Caljava, but for $90.. well, that’s a tad expensive. I studied the structure, and went to my local hardware store and purchased all of the items i needed. For this particular cake, here are the items I purchased:

  • 3/4 inch PVC pipe (the white one)
  • 2- 90 degree 3/4 inch elbow
  • 2- 45 degree 3/4 inch elbow
  • 1- cross connector ( not sure if that’s the proper name for it)
  • 4 inch PVC cutters (which work great dor cutting dowels also)
  • A small sheet of partical board
  • wood screws

I sketched up a rough draft if what I wanted my cake to look like before I went to the hardware store.
My total was roughly about $25.00. I cut a 16 inch board to use as my base, and two 10 inch rounds to use as the cake supports where I would be stacking onto. Here is a picture of my structure.

I cleaned all the pipes and flanges, and I measured how long I wanted his torso, his head etc., and used the cutters to cut where needed, then put everything together. I used the 90 degree elbows for his legs, the 45 degree elbows were used for his elbows lol and the cross conector is what I used to connect his torso to his head, and arms, and legs. Once I got him put together, I decided where I wanted to place him on the board, and once I found a placement that I liked, I then drilled the flanges to the board using the wood screws. I did this in the beginning of the week. I baked off my cakes (rainbow cakes :-)) and the following day torted and stacked them. I precut holes in my cake board so that I could slide them down the PVC pipe with ease, when stacking. I used a small round cutter to cut holes in the cake as well.

I also made RKT to use for the arms and legs of my character. I use the basic recipe, but in case you don’t have it, here it is :

3 tablespoons butter or margarine
1 package (10 oz., about 40) regular marshmallows
— OR —
4 cups miniature marshmallows
6 cups Kellogg’s® Rice Krispies® cereal

DIRECTIONS
1. In large saucepan melt butter over low heat. Add marshmallows and stir until completely melted. Remove from heat.

2. Add KELLOGG’S RICE KRISPIES cereal. Stir until well coated.

3. Using buttered spatula or wax paper evenly press mixture into 13 × 9 × 2-inch pan coated with cooking spray. Cool. Cut into 2-inch squares. Best if served the same day.

MICROWAVE DIRECTIONS:
In microwave-safe bowl heat butter and marshmallows on HIGH for 3 minutes, stirring after 2 minutes. Stir until smooth. Follow steps 2 and 3 above. Microwave cooking times may vary.

I made about 4 batches for what I needed. Sticking them to the PVC pipe was a bit tricky. I used plastic wrap to prep the arms and legs where the RKT would be. I used melted marshmallows to adhere the RKT to the PVC. I then stuck the structure in the refridgerator to firm up, and once they were hard I began to stack the cakes on, I slid them onto the pipe. I then crumb coateded the cake, and allowed it to firm up, and used a grass tip to pipe his fur detail. Once his fur was on, I iced the board, and used brown sugar for the “sand” on the ground. Brobee land is kinda brownish orange, so I thought it would go with it lol. I made a plaque similar to the YGG logo, and piped the inscription.

As I said earlier, I am still new at this, and this was my VERY FIRST 3D cake. I wanted to post this because even though I am not the best, I thought it would help anyone looking for info on 3D structures. Hope it helps. And if you have any feedback, please let me know.

Thanks :-)

Here is my finished Brobee, he stood 2 feet tall, and boy was he heavy! lol

Tags: yo gabba gabba brobee monster pvc pipe 3d cake tutorial how-to

Crys, Kitty Cakes, www.facebook.com/kittycakes21

  • Part 1: Brobee 3D cake

View all parts of PVC cake armature »

4,651 views

20 16
Share Tweet
Follow

20 Comments

John Flannery ...

Very nice , thanks for the tutorial

Uptowngirl ...

Excellent tutorial, the cake looks fab, thank you :)

candy1 ...

Wow that is very impressive!

Marissa's Sugar & Chocolate Art ...

thankyou!

Gulnaz Mitchell ...

Great tutorial! Thank you for sharing!

Toni (White Crafty Cakes) ...

Wow that’s an amazing cake! Thank you for sharing the tutorial! I’ll bet the piping took forever!!

curiAUSSIEty custom cakes ...

Great job and great tutorial!!!

Ladybug9 ...

You did an AMAZING job! Hard to believe you’re a newbie…Bravo and Thank you for the tutorial…

Crys ...

Thank you everyone for your support! It means a lot to me!!

Whitecrafty YES! lol it took me a little over an hour!~ and my hand was cramping bad!

Ladybug9 Thank you very much! I try to pick up as much as I can from everyone here on Cakesdecor and from other cake artists who are generous enough to offer advice and “know how”. Even though I am not a great cake artist yet, I feel any bit of information helps. I know it helps me lol Thank you for your kind words :0)

Marlene ...

this is a great tutorial! thank you for sharing

Crys ...

Thank you sweetartcakes :0)

Radhika ...

This is such an interesting tutorial! Thanks for sharing! And wow! That cake looks huge!

TooTTiFruiTTi ...

Amazing and to think that you pretty new at cake artistry! Thank you for the tutorial.

Crys ...

Raika It was!! lol and very heavy!

Crys ...

TooTTiFruiTTi thank you very much!