How to make wired Sugar Succulents

This tutorial was made following my ""blog post":http://mydelectabletreats.blogspot.com/2013/08/my-sweet-succulent-adventure.html "on a wedding cake project with my friend :)

Here’s how I made the sugar succulents.

You will be needing:

1. Colored gumpaste. For this project I had colored it mint green with a little moss green. Let the colored gumpaste rest before using.
2. Floral wires gauge # 22 and # 26, cut into four inches long. (gauge # may vary depending on the size and thickness of your leaf). In the photo the thin floral wire, guage #26 has a silver foil coating. It is not a naked wire :).
3. Teardrop or rose cutters. I know you are wondering why my cutter looks odd :D it is because it is an ice cream on a cone cutter. My teardrop cutters are way too big for the size I am going to make. So, I made used of what I have. You’ll see later.
4. Petal Dust: Moss Green and Old Rose.
5. Ball tool.
6. Flat medium stiff bristle paint brush.
7. Cutting Mat.
8. Rolling pin
9. Sharp Craft Knife (not in photo)
10. Foam pad (not in photo)
11. Gum glue (not in photo)
12. Styrofoam block, flower formers, drying rack. (not in photo)
13. Vegetable shortening (not in photo) – used to prevent gumpaste from sticking on cutting mat, rolling pin and from the ball tool.
14. Floral Tape (not in photo)
15. Pearl Luster dust (not in photo)

1. We will start with the bud. Roll out a small ball about 2 grams of gumpaste. If you don’t have a weighing scale, you can eye ball the size depending on how small or big you wanted to create. Another method is by using a circle template that you can purchase in your local craft store or school and office supplies store. Just roll a ball of gumpaste and let it sit through the size of the hole you wanted. Making sure that the ball sits snugly half way through the hole.

2. For the bud, I used the floral wire gauge #22. With a pliers, bend one end to form a hook. Dip that end into water or gum glue. Thread the other end into the ball until the hook is secured in the ball.
Please keep in mind that the size of the first four leaves should be big enough to wrap around the ball.

3. Let it dry. Drying time varies depending on the weather and the area you are working or where you are placing your buds to dry. Always keep it away from humidity. It is also important that the bud is completely dry when working on the next step which is attaching the leaves.

4. Succulents are known to have fat/thick leaves. So we need to roll the gumpaste into an eighth or a fourth
of an inch thick. If you have a rolling pin rings, that will do the job easier to have an even thickness.

Once rolled, I used the smallest cutter that I have to cut the first four leaves to cover the ball to make the bud. Since I’m using an ice cream on a cone cutter, I have to trim out the sides to make a clean teardrop shape.

5. Place the teardrop shaped gumpaste onto a foam pad and make an indentation using a ball tool so it will cupped perfectly with the ball. Dab some gum glue and stick it to the ball. Repeat with the remaining three leaves.

6. After all the four leaves are attached, gather the tips of the leaves and twist it to create a spiral look. Set it aside to dry. I forgot to take a photo before this was dusted :D

7. For the leaves, cut another four leaves, same size used in making the bud. Make an indentation again and stick it on the side of the bud with a dab of gum glue.This time let the pointed end upright. Pinch the ends to make a pointy end. Hang it to dry on a drying rack or stick the wire on a foam block. When it dries, dab some old rose petal dust on the pointy ends and sides of the bud and dust the the rest of the bud with moss green petal dust. Set aside.

8. For the next set of leaves you need to cut ten to twelve leaves (depending on the size of your bud). Once cut and trimmed, place your left thumb on the edge of the wide part of the leaf. Gently push it towards your two right fingers, while doing so, pinch until you get the center pointy.

9. Lay it on the foam pad. With a ball tool, starting at the middle, run it through just before the edge of the leaf. Do the same to the other side.

10. To have a nice cupped and wide look, pinch the sides of the leaf like in the photo.

11. Once you get the desired shape, you can get the floral wire gauge #26. Dip it in gum glue and thread it through the end of the pointed part of the leaf. Lay it on flower formers to dry. Do the same to the remaining eleven leaves. If you want a fuller look, just use the next large size of your cutter and make more leaves.

12. Once the leaves are dried, dust the pointed part first with old rose petal dust and the sides near the point before dusting the rest of the leaf with moss green petal dust.

13. Holding the tip of the the leaf, bend the wire down. This will make attaching to the bud’s stem easier.

14. To attach the leaf, wrap both wires (from the bud and the leaf) with a floral tape. Wrap every wire to the tip before attaching another. Continue until all leaves are attached.

15. See how lovely it is as it starts to take shape :)

You can now dust it with a pearl luster dust to give it life! And here they are … before they were wrapped and placed in the cake box.

You can vary the sizes and number of leaves to give it character and variations on your sugar succulents.

Have a great day everyone! Until next time.

Donna

Donna, Philippines, https://www.facebook.com/mydelectabletreats

3,597 views

6 14
Share Tweet
Follow

6 Comments

Goreti ...

Thanks for sharing.

MsGF ...

Very Nice! Great Tutorial

whitecrafty ...

Thank you so much, they look amazing! Great tutorial!!

Gulnaz Mitchell ...

Very good tutorial, Donna! Thank you for sharing!

Donna Dolendo ...

You’re welcome :) Thank you for the appreciation. Please do share your work using this tutorial :) would love to see how you all did.

Raewyn Read - Cakes by Raewyn ...

Gorgeous! Thank you :) xx